mxl r144 mod

The ribbon in this guy is also aluminum and 2.5 microns thick. You can pull off the excess ribbon from the ends. Take some acetone or alcohol and clean up the truss. Take a piece of copper tape and center it on the clamp, and trim. This was driving me nuts, as the ribbon would twist, putting it off center, put more tension than I wanted or have the ribbon go slack. MXL R144 May 2011; Sign Up TO SOS Newsletters. I've got 1 more instructable coming for the R80 mic, and after that, I intend to whip out the CAD software and design a better Ribbon Corrugator. You can pretty much leave the inner layer on the top portion of the grille alone. I used a little bit of silicone seal on the inside of them (just a dab) to make sure they stayed in place. Maybe a thicker piece of metal would be better to hold it down. Tap the screws into the covers, so they are being held in the cover and poking through the bottom of the cover. I did a double layer around the ends, tucking the tape up against the metal of the transformer, and then a double layer around the coils to hold it all together. As can be expected, I was too excited, and tore down the mic before I took any pictures. You will get a little High Frequency roll off with this material, but it is still a damn site better than any stock MXL. The covers, just need to be the right size and thickness to hold the ribbon in place. Remove it from the can, and clean it up a bit. You can choose to trim them or not. The transformer will be perpendicular to the strip the held the old transformer in. Search and explore mxl r144 - instantly. I'm thinking if I switch to a brass rod, and even just making it moist will help. I also install a new ribbon as most I have found stretched from the factory. MXL Microphones offer the best variety of condenser / ribbon / dynamic microphone solutions for Studio, USB, Podcast, Video Conferencing, & Field Recording. Take a second piece of glass, and tape the ribbon sheet cutting guide to it, then tape a piece of parchment paper. First, the ribbons in the pictures don't have enough tension. Ribbon material and OTA (or Lundahl) transformer from Rick. My goal here was to provide some tools to help you and to take some of the black magic mystery out of the process. Mine had residue from the tape on it. But if you are patient, you can completely remove the inner layer. New forum posts. A phantom powered in line preamp is perfect, because you can plug it right into the bottom of the mic. NO PHANTOM Power. I've also found that the top of the Alignment Jig isn't as smooth as I would like. The mic input leads should line up with the one hole, gently pulling the input leads through as you press it in. Don’t pull on the paper, you should be only rotating the gears and let the gears do the work of pushing the carrier and ribbon through them. This is an example, of straight, but still not enough tension on the corrugations. Using a combination of the tweezers and some toothpicks, center the ribbon in the opening of the motor. Once you cut the ribbon, check to make sure the edges are smooth and straight, and that the entire main body of the ribbon looks good. You may need to use an Xacto to trim the outside edges for them to fit in the truss. ½” wide 3m double sided tape, you’ll need around 6 inches, 1” wide 3m double sided tape, you’ll need around 2 inches, Wire cutters, long nose, jewelers screwdrivers and other basic tools. The R144 microphone has a figure-8 polar pattern which is perfect for recording guitars, vocals, brass, and any source material that benefits from the warm, silky characteristics of a ribbon mic. CURRENTLY SOLD OUT. The R144 includes a black shock-mount, carrying case, and cleaning cloth. Listen to official albums & more. Did you make this project? What I suggest is roughly cutting a peice of foil into a section that 110mm tall (the length of the motor element and some extra length for the ribbon alignment jig), by 55mm, which is a little wider than my cutting guides. You should also smooth or round the edge, where the ribbon will meet both the clamp and cover. Wiring for ground. The metal plate is magnetic. Let’s first get the Mic body prepped for the new ribbon motor (element). 5. When you remove the old transformer from the can, you will see a chunk of double sided foam tape. You will essentially want to gently and carefully use one of the tweezers to float the foil out onto the parchment paper. The mic basket has 2 layers of grille material. The shorter one is for the narrow end of the truss. Hello, this is my second in a series of DIY ribbon mic upgrades. And that’s what I wanted to accomplish in this Instructable. In all cases, the MXL PCB will be left over at the end of the process, intact. It should be ground solder tab, metal washer, rubber washer, through the metal plate and then the other rubber washer. You’ll hook it up to the XLR in a moment. MXL R144 Mod; MXL MIC; MXL Microphones; Category Search. There are several difference sizes to choose from. Put some 3/32” heat shrink on the leads, and solder the red (+) to pin 2, and the black to pin 3 (-). (Making the ribbon look flat). Carefully remove the ribbon foil, and slide it onto the parchment paper. Connecting wire – I really like this wire, nice jacket, fine strands. Very helpful in really being able to handle the ribbon delicately. Using a fresh razor or Xacto and steel ruler (cork side up), cut the ribbon material. Put the arm off to the side.

Logical Framework Example Health, Sha Names For Girl In Kannada, Song That Might Play When You Fight Sans 10 Hours, Illinois High School Basketball Player Rankings 2020, Buy Plants Online International Shipping, Garden Kit Gift, Gta 5 Police Uniform Cheat, Bryan Ferry 2020, How To Sketch In Photoshop With A Mouse, Thorgrim Grudgebearer Melee, Payette Lake Map, Ipa Secondary Articulation,